You would be easier to find for newcomers if you posted a link to yourself as moderator at the top of the page. Just a thought.
-
-
I'm not following
A link? email? top of what page? Who needs to find me? For what?3~ Tudor's & 1~ Coupe
Henry Ford said,
"It's all nuts and bolts"
"Start by doing what's necessary; then do what's possible; and suddenly you are doing the impossible."
Mitch's Auto Service ctr -
I could post a link at the top of this forum in the stcky3~ Tudor's & 1~ Coupe
Henry Ford said,
"It's all nuts and bolts"
"Start by doing what's necessary; then do what's possible; and suddenly you are doing the impossible."
Mitch's Auto Service ctrComment
-
My plan is put the backing plate on with two bolts as you had left it. Then using dry bearings install the hub and spindel nut. I got the radiator installation complete, water pump, inlet neck and will fill with water/antifreeze. If you do a test drive maybe keep an eye on it. I probably won't get started on this until next Monday when this cold snap breaks and I may leave the hood off. I'll be sure to give you a heads up before I bring it your way.
-
I posted a link in the community drop down menu and a couple of the sticky's3~ Tudor's & 1~ Coupe
Henry Ford said,
"It's all nuts and bolts"
"Start by doing what's necessary; then do what's possible; and suddenly you are doing the impossible."
Mitch's Auto Service ctrComment
-
? I ain't getting this... The only thing I understood is the dry bearings part and I don't understand why dry.Comment
-
Sorry Art. It was really intended just for Mitch. He is doing some work on my truck and understands why I said that.Comment
-
Why is today's Page No. 1? If the pages were numbered from the start of this Forum, then the numbers of the pages would not change and the item you noted on say page 22 would always be on page 22. Simple notes in a book would keep your info at hand at all times without doing a search every time for the same info. **** **** is terrible to find any info that one read pages ago. Think logically for this...11-27-2017, 11:59 AM -
My Judging Standards manual only goes to page 4-9. I know, I need all the updates. In the meantime, could someone post a copy of page 4-16, or would that be some kind of copyright infringement situation? I'm looking for a pic of the rear bumper arm spacer. Thanks, Smitty06-21-2017, 11:00 AM -
Ck out the new articles forum which is accessed by the link at the top. If you have an article or idea that you would like to submit for consideration just PM it to me, if published your name will be posted on the top of that listing.
These articles can only be commented on
Thanks07-09-2017, 07:19 PM -
Thanks Mitch for that link at the bottom of the page when you look at someone's topic that they post!!
Lots of interesting stuff!! And you don't have to go back to find it!10-04-2018, 11:06 AM -
I can’t find a local Convertible Top installer , so I think I will put a new Top on my Model A Cabriolet myself.
The present Top was installed in 1950 according to the former owner of the Car, and it is well fitted but it is also in need of replacement.
I did install a new Top on a Model A Roadster some years ago and it did turn out very well so I do have some experience.
...09-29-2018, 04:50 PM -
RGJS - Somewhere it states that parts can be used for three months after the end date indicated in the RGJS. What is the page number this rule is found on?11-28-2017, 10:04 PM -
Here's the link: http://www.fordgarage.com/pages/TremecT170FT.htm03-24-2018, 06:29 PM -
Things changed, and I couldn't find the OFF TOPIC section until Mitch told me the FORUMS now has a drop down menu, and it's listed there.
I posted this here, just in case someone else gets lost.09-04-2017, 09:07 PM
Comment