Announcement

Collapse
No announcement yet.

judging Standards Paint Codes

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Big hammer
    commented on 's reply
    Thanks for the picture Jim, very nice Dean :-)

  • Chevmn56
    commented on 's reply
    Wow Real nice and real clean engine compartment Dean looks awesome!

  • Jim Mason
    commented on 's reply
    It is a photo of A495, it belongs to dean

  • Chevmn56
    commented on 's reply
    Wow Real nice and real clean engine compartment Jim looks awesome!

  • Chevmn56
    commented on 's reply
    Thanks

  • Mitch
    replied
    The last set of codes i posted was from the undercarriage section. I think your question is answered. bst, bsg, bg
    Those are the blacks that were used
    Raven is gun metal blue like the spark plug bases the Jim posted

    Leave a comment:


  • Chevmn56
    commented on 's reply
    Revised 2011

  • Chevmn56
    replied
    This is what my 1-17 says in the engine tab
    You do not have permission to view this gallery.
    This gallery has 1 photos.

    Leave a comment:


  • Mitch
    replied
    Check out this thread about Raven finish

    https://www.vintagefordforum.com/for...nuts-bolts-ect

    Leave a comment:


  • Mitch
    replied
    0B8B4C2D-04A1-4C30-BDED-B07F3A85000F.jpeg

    Leave a comment:


  • Jim Mason
    replied
    Raven spark plug bases, head studs.
    Black black enamel water return pipe

    image_5707.jpg
    Last edited by Jim Mason; 01-16-2018, 09:27 PM.

    Leave a comment:


  • Chevmn56
    replied
    Originally posted by Mitch View Post
    Look at the code chart on page 1-17 / 2016
    thats where my question is R=Raven which is gloss black i believe and B= Black, Black as in satin or flat??????? or is it gloss as well?
    Last edited by Chevmn56; 01-16-2018, 09:09 PM.

    Leave a comment:


  • Mitch
    replied
    Look at the code chart on page 1-17 / 2016

    Leave a comment:


  • Chevmn56
    started a topic judging Standards Paint Codes

    judging Standards Paint Codes

    Hello all !!! i am real close to putting various engine parts back on Clyde. What started as a tune up 2 months ago, has now grown. I think i have the bug also. But in reading the Judging Standards book it makes referance to 2 paimt codes B- Black and R-Raven, now on doing some research on the internet i think R-Raven would be gloss black?????, so what is B-Black????? satin????

Related Topics

Collapse

  • Steve Plucker
    Paint schemes...
    by Steve Plucker
    In Section 1 (Engine Compartment) and Section 4 (Undercarriage) of the Standards, the paint schemes per part are spelled out.
    Now we go to Area 7 (Brake System) and very little is told about the individual brake parts being a specific "black" color.
    Can you please tell me what parts are:
    1. Satin Black
    2. Semi-gloss Black
    3. Gloss Black
    I just can not...
    04-11-2019, 12:07 AM
  • smittykid
    Correct black paint for gen., starter, oil pan, etc.?
    by smittykid
    The engine is out of my 29 Tudor being rebuilt by the folks out in Skokie, Il. While everything is off the engine-I figured now would be the time to paint the black stuff. Would Rustoleum gloss black be close? I'm not really going for a high point show car, but since everything is off and relatively easy to paint-I would like to get it close. Obviously, Rustoleum paint is readily available. ...
    08-12-2017, 07:46 AM
  • Mike V. Florida
    Japan Black
    by Mike V. Florida
    There are a few items on the A that were protected by the process called Japan Black or Japanning. The Guidelines say the parts were dull but from what I have read and seen about the process, the results were far from dull.

    So here are the questions, has anyone used the process? How glossy did it come out? Did you have it judged and what was the point result?

    Here is a formula...
    02-17-2019, 03:21 PM
  • 1930murray
    Axle part paint sheens
    by 1930murray
    What black paint sheen should the spring clamps be? (I am referring to the c-shaped clamp that clips into and around the middle leaf of each pack)

    What black paint sheen should the spring hanger (shackle) be?

    what black paint sheen should the hanger bars be?

    I am wondering why these items are not listed on sheet 4-22 in the judging standards. Are these components...
    03-21-2019, 10:56 PM
  • SeaSlugs
    28-early 29 floor board paint?
    by SeaSlugs
    So im getting a set of floor boards done - dovetailed wood plank style, all holes cut for AA with dual high pedals, holes drilled for support straps - went to old ace hardware for #12x3/4 screws with slotted head, but unsure of what to use to stain or paint them. I tested on the upper board near the pedals with black minwax polystain. Soaked in nicely to the end grain and will preserve it forever...
    09-03-2018, 10:42 PM
  • Steve Plucker
    Cad Plating and Black Oxide kits...
    by Steve Plucker
    Cad Plating and Black Oxide kits...

    Who have you found that makes the best Cad Plating and Black Oxide kits that are on the market today?

    Thanks.

    Pluck
    11-28-2018, 09:38 AM
  • Jim Mason
    Japan black
    by Jim Mason
    Here's a link to an article I wrote re:Japan black. please note asphaltum is not the same as asphalt or road tar. just as amber is not the same as pine pitch.
    http://jmodela.coffeecup.com/japan_black.html
    08-29-2017, 12:29 AM
  • greenhornet
    1931 grill shell paint for recesses.
    by greenhornet
    Mine is black on a Kewannee green car was painted grills an option? I searched online for pictures and cannot believe how many '31 Model A's are covered up with the stainless steel guard. Either pretty popular or felt necessary I guess.
    01-20-2019, 04:06 PM
  • Paul
    Original Jacks
    by Paul
    I have been collecting jacks, researching the web, and consulting the standards; now it's time for some questions.

    1. Were all Jack's painted gloss black?

    2. Were the screws and/or ratchets painted?

    3. How were they painted: sprayed, dipped, etc?

    4. What jack, if any is the most sought after?
    You do not have permission to view this gallery.
    This gallery has 1 photos.
    12-13-2018, 08:34 PM
  • Art Ebeling
    31 running board paint
    by Art Ebeling
    The Judging standards say the underside of the 31 running boards were coated with a "dull black material". What would be the best paint for that finish? Thanks, Art
    11-20-2018, 10:24 PM
Working...
X