No announcement yet.

Rain Gutters

  • Filter
  • Time
  • Show
Clear All
new posts

  • Rain Gutters

    So I am missing the whole left rain gutter on the Briggs. What options do I have?

  • #2
    AFAIK, Snyder's sells 2 piece steel replacements (about $90 a pr) The catch is you have to bend them to fit, not so easy! I'm still waiting for someone who can bend them for me....Properly! I believe that another vendor sells one piece (?) aluminum version which might be easier to bend.


    Related Topics


    • Grit Kid
      Rumble seat opening width?
      by Grit Kid
      Could someone who has a rumble measure the width of the opening. There is a antique folding table on Ebay. I need to know if it would slide into the floor. It's 36in and that might be too wide.

      From rain gutter to rain gutter...………..

      07-05-2018, 03:58 PM
    • GaryWa
      Heavy Rain Floodings
      by GaryWa
      Wishing all Model A folks and others in the flood zones in California and surrounding areas to be safe!
      01-12-2023, 12:20 PM
    • GranTudor
      30-31 Original Rain Gutters
      by GranTudor
      It has been 20 years since I took them off and restored the gutters. I have the bottom piece installed on the Tudor car but can't remember how the gutter is hooked onto the bottom piece. Could someone show me a sketch on how they snap together. Thanks Grant.
      02-23-2021, 06:58 PM
    • dmdeaton
      Rain gutters
      by dmdeaton
      tonight I started on my right side rain gutter which was missing when I bought her.
      07-22-2019, 09:21 PM
    • Mickey
      How to question....rumble/trunk rain gutter
      by Mickey
      How is the rain gutter attached to rear qtr. sheet metal?
      01-16-2019, 11:59 AM
    • Cape Codder
      Rain Gutter Attachment
      by Cape Codder
      I am trying to attach the rain gutter to my car ('30 Fordor Briggs Blindback) and this is what I have to work with in the pictures. I would like to know what is up when attaching to the body? The first picture had the head of the nails on this side in the picture. It doesn't seem correct but there were at least 18 nails that I removed so....... Lastly, is there a difference in gutter height between...
      07-07-2020, 04:22 PM
    • Farmputzer
      Fordor rail gutter
      by Farmputzer
      I'm in the process of installing my original 2-piece steel rain gutter on my 30 Murray town sedan. Is there a procedure (or trick) to getting the gutter piece to snap to the base? Do you hook the top edge and then get the bottom to snap? Use a lubricant? Persuad using a soft hammer? Or?...
      05-11-2018, 01:53 PM
    • Fomoco998
      Rumble seat rain gutter
      by Fomoco998
      Trying to figure out where the rain gutter drains to. Going to replace rear corners and want to keep them from rusting . Need opinions on best rear corners for my 30 coupe Thanks
      03-07-2018, 03:48 PM
      Touring with the model A in the rain and waterproofing.
      by BNCHIEF
      On a recent tour I was on it rained and sometimes very hard, knew about model t fords and issues in the rain but this A was my first. Some fellows experienced water in their distributors and I assume it got in there from driving down the road and water entering the distributor thru the cap locator pin I cannot imagine it coming in on the backside where the advance lever is. The front area would...
      09-24-2018, 08:06 AM
    • Terry, NJ
      Rear Fender Inner Panels
      by Terry, NJ
      OK, so I bought a rear inner panel at Hershey from Smith and Jones (good price, somewhat rusty panel) definitely usable! However, My coupe is not rusted out, it is only ragged at the bottom, There's a heck out a lot less welding by not doing the whole thing Whaddya think? Should I cut out the whole thing? Or only a strip along the bottom? Also, This panel has a tab bent 90 deg. along the bottom....
      10-30-2019, 12:10 PM