How do you remove seat backrest ? I don’t see anything holding it.
tks
tks
-
-
Welcome John03 to the VFF!3~ Tudor's & 1~ Coupe
Henry Ford said,
"It's all nuts and bolts"
"Start by doing what's necessary; then do what's possible; and suddenly you are doing the impossible."
Mitch's Auto Service ctr -
There are some L shaped brackets that you access through the rumble seat area . Some have 2 or 3 screws that go through the seat riser and the L shaped brackets. They are quite hard to reach with the rumble cushions installed unless you are way more flexible than I am . I hope this makes sense . NormComment
-
Hey John03, WELCOME to the VFF!!You wana look waaay far up da road and plan yer route because the brakes are far more of a suggestion than a command!Comment
-
Thanks, JohnComment
-
Hi All,
New member here and owner of a 1930 Model A Murray Sedan 4 door . Quick background, I was involved with Model A's as a youngster with my Father and Grandfather. Now I am 33 and my Grandfather has graciously enough gifted me an A. I am 6'3 and really had trouble driving the car at all (safely and comfortably). I was wondering if anyone could give me insight or a walkthrough on...01-31-2021, 04:50 PM -
Rumble seat cushion removal. I need to pull the rumble seat upper& lower seat cushions from my '30 Sport Coupe. Your help please in pointing out the correct procedure for this task. Thank you.05-26-2020, 10:08 PM -
I'm having trouble figuring out the exact placement fore and aft for the rumble seat riser. Anyone with pictures, measurement or suggestions? The repro I have gives very little latitude left and right so centered will have to do.04-27-2019, 05:56 PM -
Are there any suggestions to preserve original upholstery(seat & rumble seat) for a deluxe '31 roadster?10-03-2019, 06:27 AM
-
Can someone check the OEM part numbers for the '28-'31 Model A rumble seat brackets? I have two with the following numbers; A-52533 and A52534 (no dash). See attached photos. Both have W5-1 to the right of the first set. I don't know if Ford would have made a mistake with the dash and I suspect these are reproductions, however all the repros I have seen carry the same part number, A-41543 for the...You do not have permission to view this gallery.
This gallery has 3 photos.12-28-2019, 07:28 PM -
I think my rumble seat cushions are pretty good originals not a reproduction but the rumble seat floor is a fabrication. The car was restored in the fifties and sixties probably before reroductions were made for seat springs and floor. My question is this how does the rumble seat cushion on a '31 roadster fasten to the floor.I think I see holes in the repro floor platform and my seat spring has two...01-15-2019, 09:11 PM -
Have a Cabriolet that needs front Seat work, lower cushion is removed easily.
How do I get the Seat Back out without destroying attached upholstery ?
The Seat Frame is all metal bottom , it is the late style.11-14-2020, 06:30 PM -
My 30 coupe with rumble seat needs storage . Looking at under seat pan with recess but no one lists how deep for the 1930 just the 28/29 . Is this a good alternative ? Looking for any or all options.12-23-2019, 08:35 AM -
Is there some place where it shows an exploded view of the rumble seat area. Just trying to see what parts are needed to make a complete rumble seat. Thanks in advance. Hugh04-15-2019, 08:57 PM -
Tinkering with my Roadster while waiting for other parts. My rumble seat "back" cushion isn't fastening to the lid correctly. My lid has 2 slots towards the top on either side and the back cushion has 2 tabs that slip down into these slots, there is nothing on the bottom of the cushion to attach to the lid and subsequently everytime I close the lid the bottom of the back cushion rubs on...You do not have permission to view this gallery.
This gallery has 1 photos.08-01-2020, 07:55 PM
Comment