Announcement

Collapse
No announcement yet.

VFF Maintenance

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • VFF Maintenance

    The site will be down a bit @ 9:00 est on 12/11.


    DDC74602-67B7-4474-835F-5E4EBF036E5E.jpeg
    3 ~ Tudor's
    Henry Ford said
    "It's all nuts and bolts"


    Mitch's Auto Service ctr

  • #2
    Mitch shouldn't take more than 10 minutes or so to change the oil in the VFF!! Top off the radiator shoot a little grease and we're all set to go!!

    Comment


    • #3
      Well it seems i might have beat jiffy lubes time, and actually tightened the drain plug properly
      3 ~ Tudor's
      Henry Ford said
      "It's all nuts and bolts"


      Mitch's Auto Service ctr

      Comment


      • BILL WILLIAMSON
        BILL WILLIAMSON commented
        Editing a comment
        Did you OEL the horn & them 2 throttle rod "funnel" holes?
        SA Dad

    • #4
      You must have used an impact gun on the drain plug.:rolling

      Comment


      • BILL WILLIAMSON
        BILL WILLIAMSON commented
        Editing a comment
        In the hands of the SHOP IDIOT, an Impact Wrench is a DESTRUCTION DEVICE!

      • CarlG
        CarlG commented
        Editing a comment
        I have had the distinct pleasure of not being able to get a tire changed when I had a flat due to the dunderhead that used one.

      • tbirdtbird
        tbirdtbird commented
        Editing a comment
        me too, Carl, they are supposed to use torque sticks

    • #5
      There will be another maintenance deal at 11:00 pm est tonight.
      i'll get the 3/4 impact out
      3 ~ Tudor's
      Henry Ford said
      "It's all nuts and bolts"


      Mitch's Auto Service ctr

      Comment


      • BNCHIEF
        BNCHIEF commented
        Editing a comment
        Nothing to get twisted up about.

      • DaWizard
        DaWizard commented
        Editing a comment
        Yea, that didn't hurt a bit. *shudders with withdrawals*

      • CarlG
        CarlG commented
        Editing a comment
        That puts it at 7:pm here, right in the middle of "prime time" posting.

    • #6
      Carl the post was from 12/11 & 12/12
      3 ~ Tudor's
      Henry Ford said
      "It's all nuts and bolts"


      Mitch's Auto Service ctr

      Comment


      • CarlG
        CarlG commented
        Editing a comment
        I know, I saw it then. The time is all I had reference to.

    Related Topics

    Collapse

    • Mitch
      Hoarder Here
      by Mitch
      Early morning run, filled my 24' trailer,, and there is more hidden in boxes
      Mission complete

      ...
      08-26-2017, 10:24 AM
    • Michael M
      Model A’s in the Depression
      by Michael M
      Here is an interesting site on Fords. The link will take you to photos of A’s in the era, but there is a lot of other good information there as well.

      http://vintagefordfacts.blogspot.com...epression.html...
      01-07-2018, 09:32 AM
    • MontanaRed
      Took the Carb off today!
      by MontanaRed
      Need some opinions, Took my carb off today and this is what I found under the bowl, bowl doesn't have any holes in it and all the valves seem in good working order but that rust corrosion is pretty bad, also there is a small hole at 11oclock on the first picture it appears to be a machined hole, is it suppose to be there? Float has some dents in it also. Soaking it in evapo-rust overnight now. So...
      You do not have permission to view this gallery.
      This gallery has 3 photos.
      10-12-2018, 05:25 PM
    • pooch
      My first rod, a 28 roadster.
      by pooch
      I started with this. more to come...

      I only wanted the cowl, as I was going to build extended doors, but the door hinge screws were rusted on so I gave the guy another $100 , and I was glad I did when I got around to building it.


      Scored an already boxed A chassis and a few more bits



      HR holden independent front end with discs.

      ...
      08-29-2018, 07:01 PM
    • DaWizard
      Coolant Filters !
      by DaWizard
      Well folk, seems like my brain is working overtime today, and I have a couple of subjects to broach, least of all is the coolant filters.

      http://www.ganofilters.com/

      I have had one of these inline before the radiator since I can't remember, and have been cleaning it a minimum of once a week whether it needs it or not, and it seems it always needs it. Well, today I pulled
      ...
      08-18-2017, 07:13 PM
    • pooch
      Some pics from the swap yesterday
      by pooch
      Ford swap at Eastern Creek on july 28.

      34 cabriolet from Argentina.

      37 sedan.

      1920 T truck.

      In the car park was this older build T bucket, 48 ? Sedan, 48 ? convertible.

      Was a bit of speed gear there, and a complete lincoln V 12 motor in bits.
      ...
      07-28-2018, 06:44 PM
    • Larry Jenkins
      Brace & Larry's, 1930 CCPU Build Thread
      by Larry Jenkins
      From a basket case to a jewel..

      Part 1


      This is a pictorial journey through a 1930 CCPU restoration by me and the next owner. I had to sell it partially completed because of my wife's health issues. It was bought by a gentleman in Missouri who is now in the final stages of the restoration. Brace's VFF Name is "Pickemup."


      The pictorial demonstration...
      02-15-2018, 11:59 PM
    • Mitch
      "Lucy" 30 Tudor Build / Diary
      by Mitch
      AER long block, 5.5 head, 3:54 gears, Bergs rad, and a Tom W genny








      ...
      05-29-2017, 10:50 PM
    • pooch
      From last sunday's show at Kiama NSW
      by pooch
      A few pics....



      Lincoln V12 with a hidden legal exhaust under and electric gate valves when the noise is to be put straight out the top.



      Note nailed boards for a roof and you can guess what FNLO means.





      Supercharged T coupe.

      ...
      09-11-2018, 03:10 AM
    • Mitch
      Valve Stems, Installation, Metal Stem
      by Mitch
      Metal Valve Stem Installation Procedures

      Courtesy John Carter!


      Usually the hobbyist purchases new tubes with the metal stems already installed. If you want to convert your old tubes over or just install the metal stems yourself this may help you out.

      ...
      10-17-2018, 08:34 AM
    Working...
    X