Announcement

Collapse
No announcement yet.

Cowl light wire bracket

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
    No photos found.
Previous template Next

Related Topics

Collapse
  • fred93
    Cowl Light Wiring Info
    by fred93
    Original thread


    I need to see some pictures or drawings of how the wires are routed for a 29 Tudor. It has cowl lights. I have attached some pictures that I took before disassembly but they do not seem correct.
    You do not have permission to view this gallery.
    This gallery has 6 photos.
    11-18-2017, 11:43 AM
  • fred93
    29 Tudor electrical wire routing
    by fred93
    I need to see some pictures or drawings of how the wires are routed for a 29 Tudor. It has cowl lights. I have attached some pictures that I took before disassembly but they do not seem correct.
    You do not have permission to view this gallery.
    This gallery has 6 photos.
    11-18-2017, 11:43 AM
  • vonheine
    Cowl light wire pathway
    by vonheine
    Does anyone have a picture of the correct run of the cowl light wires through the “cockpit? The wires come out of the special nuts that bolt the brackets to the side of the car, but how did Ford run the wires through the cabin? How did Ford run the wire from the passenger side cowl light over to the harness side?My wires are a rat’s nest, especially since the car has turn signals that I believe...
    05-06-2019, 05:48 PM
  • jack.kuehn@gmail.com
    Cowl light conversion to turn signals
    by [email protected]
    I'm installing turn signals in my 30 deluxe phaeton. I bought a cowl light conversion kit from Mac's. It seems that the socket and 2 filament bulb assembly, together with the new reflector with an elongated hole will not fit inside the body of the cowl light. Anybody else run into this problem?
    03-02-2021, 08:09 PM
  • Rumbler
    Cowl welt ending at bottom of cowl
    by Rumbler
    I've searched through the fine point photos but haven't found a closeup at the bottom of the '28-'29 cowl welt. Where does it stop and is it just cut straight off or tucked in somehow?
    06-18-2020, 04:32 PM
  • JohnB15632
    Cowl Lights
    by JohnB15632
    For you guys who are running cowl lights, do you only light them on one setting or do you run will the cowl lights lit all of the time?

    I wired mine in accordance with the wiring diagram which identifies that the cowl light are switch on and off and do not light when the head lights are on.

    Thanks,
    You do not have permission to view this gallery.
    This gallery has 3 photos.
    01-27-2020, 08:39 PM
  • DBaldwin
    Cowl bands
    by DBaldwin
    Seeing as though I’ve been unable to acquire a cowl band ( unless I’m willing to give up the left one) I noticed that 32 cowl bands are available how much different are they to a 30-31? Can I modify one to be acceptable? Remembering that it’s going on a ccpu so it will get painted black anyways. Thoughts and or suggestions?...
    08-08-2021, 09:16 PM
  • popsjohn
    Cowl Light Work
    by popsjohn
    This is a newbie question. How do I take the lens off the cowl lights on my 1930 Town Sedan? I want to clean and polish the reflector. Should I take the whole light, bracket off of the car to do this? There must be an easy way/trick to remove the lens but I don't want to use force the wrong way and break something. Do I remove the screw in the back?
    04-04-2020, 09:43 AM
  • JohnB15632
    Cowl Light Crossover Wire
    by JohnB15632
    I have installed the cowl lights on my 31 SW 4D TS. I purchased a cowl light cross over Wire. In the package with the wire was a drawing B-14426 (attached). This drawing references two harnesses,

    1. #11647 HL Harness and,
    2. #13412 Harness.

    Question, does anyone have copies of the drawings?
    Can anyone tell me how and where to obtain these drawings?...
    You do not have permission to view this gallery.
    This gallery has 1 photos.
    07-06-2019, 04:38 PM
  • Art Ebeling
    Cowl band install
    by Art Ebeling
    I put my original 31 cowlband installed just finger tight today. When I hold the cowl lamp arms against the cowl band there is a gap between tahe arm and the body. Do the lamp arms get tightened enough to close that gap. I had two cowl lamp arms break when shipped from the plater so I am not wanting to force these....
    You do not have permission to view this gallery.
    This gallery has 1 photos.
    11-26-2017, 02:32 PM

Unconfigured Ad Widget

Collapse
Working...
X