I brought my "new" 29 Tudor home Friday. A frame off restoration in 95 that was never finished. Its missing the horn/light rod, light switch and wiring loom. I've seen warnings about imported switch bodies. Who offers the best deal on a US made part? The car has the 7 tooth steering.
Announcement
Collapse
No announcement yet.
Recommendations needed for light switch
Collapse
X
-
3~ Tudor's & 1~ Coupe
Henry Ford said,
"It's all nuts and bolts"
"Start by doing what's necessary; then do what's possible; and suddenly you are doing the impossible."
Mitch's Auto Service ctr
- Top
- Bottom
Related Topics
Collapse
-
by franknHas anyone cut the lower half of light switch to get it over wire instead of taking all your wiring loose and starting over Would JB weld it back together after getting it put on
-
Channel: Model A Forum
07-02-2020, 09:28 PM -
-
by Tom RodeI have run into another "issue" with the A, I turn on the headlights and first time I make a turn the switch moves to the off position with the turning of the wheel. Does not move from off with additional turns though. Thinking there is some kind of bushing of something that may just need lubrication. Is there any adjustment here, of should I just try to get some light oil around the...
-
Channel: Model A Forum
11-09-2019, 07:53 AM -
-
by HarryjamesGood Morning Everyone and greetings from Sioux Falls South Dakota. I would like to ask for some advice about fitting a new light switch on a 1929 Model A Tudor. The car came t me from a friend with a request for help. The old switch was laying in pieces at the bottom of the steering column and the car has the two light system. I looked at the parts and realized that the little C clip was missing and...
-
Channel: Model A Forum
08-08-2020, 10:44 AM -
-
by myturnNew to the group. I got a 1928 Model A Coupe. I have been reading the good information about the light switch. Found that my light switch is upside down. To turn it do I also need to turn the plate where the groove go in? If so, is it as simple as unbolting and turning?You do not have permission to view this gallery.
This gallery has 3 photos.-
Channel: Model A Forum
05-20-2023, 09:09 AM -
-
by OldgearzI looked briefly for concise instructions for how to assemble the horn/light switch spider and couldn't find info. So I invented my own and will pass them on. This assumes light switch is wired for inside light handle to be in "off" position when it is at 6:00 and low and high beams one click left and right. Always note orientation of spider forks in relation to the orientation of the...
-
Channel: Model A Forum
03-16-2023, 07:03 PM -
-
by CaptndanLooked and couldn't find it. Is there an explode view of how the light switch goes together? Thanks
-
Channel: Model A Forum
04-16-2021, 09:22 AM -
-
by canadian29 Fordor, column out of car , replaced horn rod wire, wheel back on , lubricated top bushing under horn button on reassembly. Spider , spring and clip assembled , Question is , is it normal for light switch lever to follow on times the steering wheel when rotating? This never done this before , just wondering if its because column is not in car with bottom section of light switch installed. any ...
-
Channel: Model A Forum
04-06-2018, 05:42 PM -
-
by bosticjbMy 28 model A light switch rattles while driving , any fixes ? appreciate any help
-
Channel: Model A Forum
10-11-2019, 06:21 PM -
-
by merjohnThe light switch that is on our 31 truck has 4 contact points. The new wiring harness has 3 groups of 3 contacts. Is this normal?...You do not have permission to view this gallery.
This gallery has 1 photos.-
Channel: Model A Forum
07-22-2018, 09:07 PM -
-
by Cape CodderWHAT DO MOST DO? Bit of a debate with the Bailing Wire that holds the Light Switch at the bottom of the Steering Column. Is the Bailing wire installed in the hole of the Switch OR JUST belowthe hole?
-
Channel: Model A Forum
05-01-2022, 06:48 PM -
Unconfigured Ad Widget
Collapse
Comment